STMicroelectronics Development Tool Motor Controller for STL110N10F7 for STSPIN32G4, STL110N10F7

ดูหมวดหมู่นี้

ยอดรวมย่อย (1 ชิ้น)*

THB7,663.26

(ไม่รวมภาษีมูลค่าเพิ่ม)

THB8,199.69

(รวมภาษีมูลค่าเพิ่ม)

Add to Basket
เลือกหรือพิมพ์จำนวน
หมดสต็อกชั่วคราว
  • 1 ชิ้นพร้อมจัดส่งจากคลังสินค้าต่างประเทศ
  • เพิ่มอีก 1 ชิ้นจะส่งได้หลังจากวันที่ 30 มกราคม 2569 ไปอีกประมาณ 7 วันทำการ
ต้องการสินค้าเพิ่มหรือไม่ ระบุจำนวนและคลิก ‘ตรวจสอบวันจัดส่ง’ เพื่อดูข้อมูลเพิ่มเติมเกี่ยวกับสต็อกสินค้าและการจัดส่ง
ชิ้น
ต่อหน่วย
1 +THB7,663.26

*ตัวบ่งบอกราคา / price indicative

RS Stock No.:
219-4216
หมายเลขชิ้นส่วนของผู้ผลิต / Mfr. Part No.:
EVSPIN32G4NH
ผู้ผลิต:
STMicroelectronics
ค้นหาผลิตภัณฑ์ที่คล้ายกันโดยเลือกคุณลักษณะอย่างน้อยหนึ่งรายการ
เลือกทั้งหมด

Brand

STMicroelectronics

Product Type

Power Management Development Kit

Power Management Function

Motor Controller

For Use With

STSPIN32G4, STL110N10F7

Kit Classification

Development Kit

Featured Device

STL110N10F7

Kit Name

Development Tool

Standards/Approvals

RoHS

STSPIN32G4 demonstration board for three-phase brushless motors


The EVSPIN32G4 is a demonstration board based on the STSPIN32G4 system in package and STL110N10F7 power MOSFETs. The STSPIN32G4 integrates in a 9x9 mm VFQFPN package, a triple high-performance half-bridge gate driver with a rich set of programmable features and one mixed signal STM32G431 microcontroller.

The integrated operational amplifiers for current sensing, the drain-source voltage sensing of each power MOSFET and comparators for overcurrent protection make it a fully integrated solution for motor control.

Thanks to the integrated voltage regulators both the gate driver and control logic supplies can be generated starting from the motor supply without dedicated circuitry.

The board ensures a full evaluation of the STSPIN32G4 and is designed for driving three-phase brushless DC motors and provides an easy-to-use solution for STSPIN32G4 evaluation in different applications such as power tools, e-Bikes, fans, and home appliances.

The board can be configured in three-shunt or single-shunt supporting both sensor-less and sensor-based control algorithms.

The Arduino connector enables the EVSPIN32G4 to be interfaced with expansion boards, such as MEMS sensors or Bluetooth transceivers, while predisposition for CAN bus allows interconnection with master or slave modules to build complex motion control systems.

The on-board ST-LINK/V2 programmer speeds up and simplifies the debugging of microcontroller firmware.

Key features


  • Input bus voltage from 10 V to 75 V with dedicated monitoring

  • Power stage based on the STL110N10F7 power MOSFETs with output current up to 20 Arms (with heatsink mounted) and protected to overcurrent conditions

  • STSPIN32G4, high performance three-phase motor controller with embedded STM32G431 MCU:

    • 32-bit ARM® Cortex®-M4 MCU+FP

    Up to 170 MHz clock frequency

    CORDIC mathematical hardware accelerator for trigonometric function

    128 kB Flash memory with proprietary code readout protection (PCROP), securable memory area, 1 kB OTP

    32 kB SRAM memory with HW parity check

    2 x advanced timers for motor control, 16-bit with up to 6 x PWM channels each

    8 x general purpose timers

    2 x ADCs 12-bit resolution (up to 19 channels) with 4 Msps conversion rate

    4 x 12-bit DAC channels

    4 x ultra-fast rail-to-rail comparators

    3 x rail-to-rail operational amplifiers usable also in PGA mode

    Internal high precision voltage reference

    Up to 40 GPIOs

    Full set of interfaces: I2C, SPI, UART and CAN

    VCC buck converter up to 200 mA, with programmable output and embedded MOSFET

    3.3 V LDO linear regulator up to 150 mA

    Low quiescent linear regulator for MCU supply in standby mode

    Regulators with full set of protection features; thermal shutdown, short-circuit and overload protections

    75 V rated gate drivers with 1 A sink/source current and embedded bootstrap diodes

    Drain-source voltage sensing of each power MOSFET

  • Three-shunt or single-shunt configurable current sensing

  • Digital Hall sensor and quadrature encored input

  • ST-LINK/V2 programmer and debugger

  • Arduino UNO connector

  • Predisposition for CAN bus

  • NTC sensor for power stage temperature monitoring