Electromen OY, DC Motor Controller, Potentiometer, Voltage Control, 12 48 V dc, 50 A

  • RS Stock No. 773-6844
  • หมายเลขชิ้นส่วนของผู้ผลิต / Mfr. Part No. EM-243C
  • ผู้ผลิต / Manufacturer Electromen OY
ข้อมูลทางเทคนิค / Technical Data Sheets
Legislation and Compliance
RoHS Certificate of Compliance
COO (Country of Origin): FI
รายละเอียดสินค้า / Product Details

EM-243C DC Motor Controller

EM-243C is a full bridge DC-motor starter. It is designed to work with DC-motor in applications where some special functions are needed. Starter has adjustable acceleration and deceleration ramps, which make possible the smooth starts and stops. Adjustable current limit protects motor against overcurrent and it can also be used as an end-stop. This device has also two settable speeds, which are useful
in positioning applications. Control inputs FW and BW start the forward and backward run. STOP is for the motor shut-down but there are also available individual limit inputs for FW and BW directions. SPEED-2 input activates preset speed-2, but it can also be used as input for analogue speed control signal 0-5V. FAULT terminal has at the same time input and output function, the pin is normally high, but is pulled down in overheat and conditionally also in current trip situation. If FAULT-line is pulled down externally, it will cause a stop and prevent the new start. For example, it is possible to link fault pins of several units together and achieve a synchronous stop. There are 2 selectable control modes, continuous and impulse. In continuous mode the motor runs as long as the control is active. In impulse mode a short command starts the motor, and only a new impulse will change the status.

Features & Benefits

Small size High current output
Current limit
Zero current limit
Speed setting
Flexible control inputs
Impulse / continuous mode
Rail base mountable
Digital parameter setting
C version card compatible with A version card
C firmware can be loaded A version card
C version new features-
+ Freewheel options parameter
+ 2kHz or 16kHz pwm frequency selects
+ Current limit analogue input
+ Speed and direction operating mode
+ Fan and Brake available in board 243C v.2
+ Extend operating voltage in board 243C v.2

คุณสมบัติ / Specifications
คุณสมบัติ Value
Supply Voltage 12 48 V dc
Current Rating 50 A
Voltage Rating 12 V dc, 24 V dc
Compatible Motor Type Permanent Magnet
Control Input Potentiometer, Voltage
Mounting Style DIN Rail Mount, Panel Mount
Length 107mm
Width 40mm
Depth 72mm
Dimensions 107 x 40 x 72 mm
Operating Temperature Range -40 +60 °C
15 มีของพร้อมจัดส่งภายใน (In stock for delivery within) 5 - 8 วันทำการ (working days)
ราคา / Price Each
THB 6,652.26
(exc. VAT)
THB 7,117.92
(inc. VAT)
Units
Per unit
1 +
THB6,652.26
Related Products
This range of cost effective low voltage dc. ...
Description:
This range of cost effective low voltage dc. motor controllers are suitable for use with permanent magnet dc. motors up to 12A. The boxed version is protected to IP22.,Comprehensive instruction sheet supplied. Adjustable maximum and minimum speedsIR compensationAdjustable overloadFused input ...
This module is a 4-quadrant, linear output driver ...
Description:
This module is a 4-quadrant, linear output driver which is suitable for driving small dc. motors and gear motors up to 60 watts. Only single polarity voltage supply is required to achieve bi-directional motor speed controlEmploys armature feedback technique to ...
The ADS50 is a powerful servo amplifier for ...
Description:
The ADS50 is a powerful servo amplifier for the control of brushed permanent magnet dc. motors. Four operating modes can be selected by DIP switches on the amplifierSpeed control using tacho, encoder or IR compensation or torque (current) control are ...
Suitable for permanent magnet and wound field dc ...
Description:
Suitable for permanent magnet and wound field dc motorsSupply 12 or 24Vdc battery or linear power supplyContinuous rating 24A, maximum current limited to less than 36AAdjustable electronic current limit up to 36ASpeed control by potentiometerSoft startHeatsink thermally protectedRunning/Fault/Trip ...